Any scrap yard with V4’s near Helsingborg

Forum / Övrigt / Allmänt / Any scrap yard with V4’s near Helsingborg

  • Författare
    Inlägg
    • juli 14, 2006 kl. 22:26 #14524

      It never rains but pours! I started servicing the rear brakes on my Saab 96 V4 71′ and found that the wheel back plates (bromssköld) are badly rusted, the brake brackets on the axel arm are just rust, and most of the nuts have been put on with a pair of pliers. There is no way I can repair the parts and must look for virtually a complete rear axle assembly for the car. I know there is a scrap yard near Goteborg that has a few V4’s but does anyone know of a scrap yard near Helsingborg that has V4’s that I might salvage the parts from, or does anyone have a V4 they are stripping that would have the parts and they would be interested in getting rid of them. The most important is the ”bromssköld” and the ”bakaxel med axeltappar” (left hand side).

      Best Regards

      Gary A McConnell

        juli 15, 2006 kl. 08:06 #96617

        Try these!

        Granaths Bilskrot
        Tel. 046-523 75
        Plantskolev., Box 20, 24032 FLYINGE (Eslöv)
        Vi demonterar ca 1500 krockskadade bilar per år.
        Vi är medlemmar i SBR samt certifierade av BPS
        http://www.granathsbilskrot.se/

        Thomassons Bilskrot AB
        Tel. 042-16 82 80
        Lagerg. 24, 25464 HELSINGBORG
        Thomassons Bilskrot AB köper krockskadade bilar från
        försäkringsbolag och säljer delar ifrån dessa.
        http://www.thomassonsbilskrot.se/

        Hasanovs Bilservice
        Tel. 042-823 88
        Stationsv. 5, 26790 BJUV

        Arons Bildemontering AB i Malmö
        Tel. 040-94 35 05
        Jägersrov. 181, 21375 MALMÖ
        Arons är idag ett av landets största demonteringsföretag
        och grundades 1965. Här demonteras ca 3000 bilar per år.
        http://www.aronsbildemontering.se/

        At Hasanovs in Bjuv I´ve found V4 parts.
        Good luck.

          juli 15, 2006 kl. 09:27 #96618

          Thanks!

          Have tried contacting them, some are closed for the weekend or on holiday, Arons looked but did not have it, Hasanovs will look for the part. Will keep searching.

          Best Regards

          Gary A McConnell

            juli 19, 2006 kl. 13:32 #96619

            Hi

            I am starting to run out of options with finding the parts for the car. Tried all the scrap yards, and a few more but nothing going. I just took it in for besiktning and it failed because the plates under the rear spring were rusted. So I now need to try and find a set of them as well, anyone know where I can get the plates from.

            Best Regards

            Gary A McConnell

              juli 19, 2006 kl. 14:37 #96620

              The plates UNDER the springs? Do you mean the plates that are bolted to the rear axle and support the springs lower ends? I have loads of those. I do not have the U-shaped brackets.

              Mail me your addresse and I’ll send a pair to you.

                juli 19, 2006 kl. 14:46 #96621

                Mats – Thanks for the quick response. I have sent an email with the details.

                  juli 19, 2006 kl. 18:26 #96622

                  [image]http://www.saabklubben.com/ubbthreads/attachments/571114-avgas.jpg[/image]

                  You can use one of these exhaustgizmos as a U-shaped bracket. Get one that fits in the holes in the springseat and use the U-part. Take care when you remove the screw if it is rusted! (The third hole in the springseat.)

                  The springseats are in left and right versions!

                  /B

                  bengt@akesson-motorsport.se

                    juli 25, 2006 kl. 16:02 #96623

                    Bengt – Went to Mekonomen with one of the old u-bolts and found a match, 28 mm ”rørklamma”. All dimensions the same, length, width, thread diameter and length. 12.50 each.

                    One thing I did find that is not shown in the parts manual is a spacer under the spring seat between the two shafts of the u-bolt. Does anyone know if the spacer is standard or if it has been fitted afterwards.

                    Gary McConnell

                      juli 25, 2006 kl. 19:01 #96624

                      /B

                      bengt@akesson-motorsport.se

                    • Du måste vara inloggad för att svara på detta ämne.