1740cc-dubbelblås loses oil

Forum / Övrigt / SSR / 1740cc-dubbelblås loses oil

Visar 15 inlägg - 1 till 15 (av 26 totalt)
  • Författare
    Inlägg
    • september 1, 2004 kl. 11:44 #11775

      Hej!

      I have a problem with my 1740cc-dubbelblås engine with korsinsug (Weber DCOE).

      The engine is new rebuilt with new pistons and bearings. It is all new sealed, but it loses engine-oil.

      I have put in a new oljetrag-seal and new sealing-ring at the crankshaft. But it is losing oil again. And now it also starts losing oil at the insugspackning.

      What can I do? Why is it starting to leak oil again, although the seals are all new…

      Kind Regards,

      Erik

        september 1, 2004 kl. 12:12 #82435

        How much ?
        Is it only when you driving or is it leaking when the engine is shut off ?
        Does it bluesmoke when you start it or when you accelerat or all the time (cold or hot engine) ?
        Have you tryed to screaw the bolts for the insug
        (mainfold ?) in the right order and with right åtdragningsmoment in swedish (dont know what the word is in English)I think that you have to do it twice ?
        Do you lose any oilpreaser (oljetryck)?
        Does it come from rear or frontpart of the engine ?

        Per/Haninge

          september 1, 2004 kl. 12:22 #82436

          Hej!

          The oil only comes out when the engine is driven, not when engine shut of.

          I have screwed the manifold-bolts twice, in correct order and with the correct torque (åtdragningsmoment), but it is losing oil on the rear-end of the manifold, where the distributor (fördelare) is, and on the 2 screws in the middel of the manifold. :confused:

          The other problem is oil coming out of the (brand-new) seal-ring on the crankshaft. And it looks like the oljetrag is also not perfect sealed, although I have already put in a new seal there…

          The oil-pressure is perfect all the time, always 6,5 bar oilpressure.

          I will take the engine out again to seal it all new again, but it is strange, because everytime I did this, it only lasted for short time and then losing oil again…

          Tack!

          MVH,

          Erik

            september 1, 2004 kl. 13:46 #82437

            Min motor läcker olja också, men inga stora mängder.

            Jag tror det läcker mäst vid remskivan fram så den skall bytas i vinter.

            Erik:
            Hur mycket olja försvinner ur din motor?????

              september 1, 2004 kl. 14:32 #82438

              sounds to me that you do not have any crankcase ventilation ?

                september 1, 2004 kl. 14:44 #82439

                could it be a broken cylinder head gasket…then maybe it can infect the crankcase pressure so it is to high?

                  september 1, 2004 kl. 14:56 #82440

                  This sounds like a role-model case of non-functioning crank case vents.

                    september 1, 2004 kl. 15:37 #82441

                    Hej!

                    I think I should have a closer look to the crank-case-ventilation, as I already had problems with it on this engine before the rebuild. But I thought the pressure on the crank-case was due to broken piston-rings, that was why I had the engine rebuilt with new pistons.
                    I will check that as soon as possible.

                    It loses much oil, like 0,5l in 200km.
                    The head-gasket is just new (copper-rings), so this one is ok. No water going away, full pressure on all 4 cylinders.

                    Mycket tack!

                    MVH

                    Erik

                      september 1, 2004 kl. 19:22 #82442

                      HELLO ERIK
                      check the gasket (insugspacning) maybe the cylinderheads do not fit the korsinsug.Then the oil goes into the engine

                        september 1, 2004 kl. 20:43 #82443

                        Hej uffepuffe67!

                        The oil is running out of the engine, it is not burnt.

                        But I have to check the insugspackning anyway…

                        I had a look at the crank-case-ventilation now. Everything looks like it should be… :rolleyes:
                        All tubes ok, nothing blocked.

                        Erik

                          september 1, 2004 kl. 23:43 #82444

                          ok
                          A very usual problem is if u tightend the valve cover(ventilkåpan) to much.Then it bends and leaks betveen the bolts

                            september 2, 2004 kl. 15:26 #82445

                            Citat:


                            Ursprungligen postat av uffepuffe67:
                            [qb] ok
                            A very usual problem is if u tightend the valve cover(ventilkåpan) to much.Then it bends and leaks betveen the bolts [/qb]


                            Ah yes, I know that problem, already had that…

                            Erik

                              september 2, 2004 kl. 17:23 #82446

                              Hi Erik,

                              You are not alone having a mysterious V4 engine oil leak. I have a similar problem with a standard engine for a 96 -76. It continues to leak oil although I have checked, changed and sealed most joints.

                              Furtehr hints anyway:
                              Have you carefully tightened the balance-shaft cover at the back of the engine?
                              Are you sure that you have not pushed the crankshaft ”simmering” too far forward?
                              Are you sure that the locking bolt for the balance shaft pulley is still in place ?

                              I lost the bolt on one of my Sonett IIIs and had oil leaking out between the pulley and the balance shaft end!

                              Hope you will find finally where the leak is on your engine.

                              Best regards,

                                september 2, 2004 kl. 18:41 #82447

                                I was told to put blue silicone on the manifold gasket. Specially on the cork fittings. The blue silicone was also recommended to prevent air leaking between the carburettor and the manifold. Be sure that the parts are clean before.
                                I once have oil leaking from the fuel pump, the oilpressure contact and off course from the front end of the balance shaft.
                                ///Harald

                                  september 2, 2004 kl. 19:19 #82448

                                  Hi again!

                                  Thanks for the tipps! :applad:

                                  I now have removed the valve-covers and the manifold. The manifold was leaking at the rear-end. I had put silicon-sealing on the manifold-gasket, but only on the underside. And guess what, the oil pressed through on the upper side…
                                  Ok, so I have to seal this one again.

                                  The second thing is oil coming through the two middel-screws on the manifold. I will put copper-rings under the nuts there, that worked on another engine, although I am currious why there is oil coming up…

                                  Then I will have a look at the simmering again. I think I pushed it to far in… :rolleyes:

                                  The balance-shaft cover at the back of the engine is sealed with silicon already and it was ok last time I had the engine out. But I will check again.

                                  I also had a look at the crankcase-ventilation again, but it all looks ok. Everything is free, no pipe blocked or anything. So I think this one works ok. If it was not ok, then there would have been oil coming up through the oil-checker!? There is no oil coming up.

                                  I keep you posted about how it is going on. But I wont do anything on the car till next week, because tomorow I have to do other things, and then I will be in Sweden for the Saab-market in Gistad. :tumme:

                                  Best Regards,

                                  Erik

                                Visar 15 inlägg - 1 till 15 (av 26 totalt)
                                • Du måste vara inloggad för att svara på detta ämne.